ToneX Capture Training Failure

Forum for ToneNET - AmpliTube TONEX and AmpliTube 5’s preset sharing community.
Together we rock nonstop

ToneX Capture Training Failure

Postby Jmp100@1 » Sat Mar 18, 2023 10:25 pm

To get familiar with Capture I cabled up a dirt pedal for testing. I'm using a Arturia MiniFuse 2 and tried both @ 48Khz and 44.1Khz. Training fails on all settings. Capture goes ok, I've tried lowering volume levels without any success. Training attempts to establish network then all fails.

I'm using on a new iMac a few months old.

Office iMac Retina 5K mid 2020
27” i7 3.8Ghz 8-Core Intel i7
8GB 2667Mhz DDR4
AMD Radeon Pro 5500 XT 8 GB

Ventura 13.2.1

MiniFuse 2 is connected to a USB hub, that shouldn't be an issue, I have external drives on it without issue.

Image

Running out of options, if I can't get it to work, I'll send it back.
Jmp100@1
 
Posts: 10
Joined: Wed Mar 08, 2023 2:44 am

Re: ToneX Capture Training Failure

Postby Jmp100@1 » Sat Mar 18, 2023 11:12 pm

I tried again with the minifuse 2 usb'd to the imac, no hub. Same thing. I then took the pedal out of the loop to test as a clean signal. Failed again.

I'll be sending the Capture back, it doesn't work with this new mac.
Jmp100@1
 
Posts: 10
Joined: Wed Mar 08, 2023 2:44 am

Re: ToneX Capture Training Failure

Postby Jmp100@1 » Sat Mar 18, 2023 11:27 pm

Tone X Engine v.1.1.2 - build number: b2302
Date: 2023-03-18-15-53-50

- Model Info -
Target: Stomp
Training Modality: 1

- System Info -
Platform: Apple MacOs
Project Directory: /Users/xxxxxx/Documents/IK Multimedia/TONEX/Modeler
Training In File:
Training Out File: /Users/xxxxxx/Documents/IK Multimedia/TONEX/Modeler/TXMM_Capture.wav
Cuda available: no

- Device Info -
Input Device: MINIFUSE2
Output Device: IMACSPEAKERS
Buffer Size: 512
Sample Rate: 44100

- Training Info -
ERR_CODE.ERROR_ON_LATENCY
exception called. Error Message sent. Now Exit
Jmp100@1
 
Posts: 10
Joined: Wed Mar 08, 2023 2:44 am

Re: ToneX Capture Training Failure

Postby Jmp100@1 » Mon Mar 20, 2023 3:44 pm

Jmp100@1
 
Posts: 10
Joined: Wed Mar 08, 2023 2:44 am

Re: ToneX Capture Training Failure

Postby Jmp100@1 » Tue Mar 21, 2023 12:28 am

I've tried everything, buffer range changes, changed cables, ground lift. Quite a bit of latency using high buffer settings. I tried two different pedals, same results.

The 3rd level test input is very very touchy coming back from capture, clips very easy almost instantly when in the yellow using the MiniFuse 2. Clipping produces a constant oscillating tone.

I tested inputs and outputs, both channels of the minifuse, inst. in, out to imac. No issue setting levels. Functions properly.

I tested ToneX Capture Line In using guitar, 0 attenuation, To Amp > Bose input. No issues.

Could it be the Arturia MiniFuse 2 is not compatible with Capture? If so what economical substitute?

I wired up initially as this below, then configured as Capture required for stomp.

https://www.ikmultimedia.com/products/tonexcapture/
Jmp100@1
 
Posts: 10
Joined: Wed Mar 08, 2023 2:44 am

Re: ToneX Capture Training Failure

Postby Jmp100@1 » Tue Mar 21, 2023 2:34 am

I decided to test the minifuse without capture. Minifuse Line out 1 > input 1, guitar input 2. 44.1 Khz, set the levels, level 1 sensitive as it was with capture attached. Training exited.

I'm guessing Arturia MiniFuse is not compatible with Capture.
Jmp100@1
 
Posts: 10
Joined: Wed Mar 08, 2023 2:44 am

Re: ToneX Capture Training Failure

Postby Jmp100@1 » Wed Mar 22, 2023 12:18 am

I got it thru training with a dirt pedal. As it turns out my monitor level was a bit high. Profile sounded terrible, I'll delete and do it again til I get a good profile.
Jmp100@1
 
Posts: 10
Joined: Wed Mar 08, 2023 2:44 am

Re: ToneX Capture Training Failure

Postby Jmp100@1 » Sun Apr 09, 2023 1:34 am

As it turns out after several tries, various configurations attempting to capture a couple pedals it failed. No matter how it was setup the capture signal was always clean not the device to be profiled. Either the MiniFuse2, ToneX Capture or both are incompatible. Keeping the ToneX pedal, Capture and MiniFuse2 are going back. My best guess is the MiniFuse as the culprit, 2 in, 2 out.
Jmp100@1
 
Posts: 10
Joined: Wed Mar 08, 2023 2:44 am


Return to ToneNET preset sharing community